Boring & Big Bore · Geometry tool

Overbore Displacement Calculator — Bored .030, .040, .060 and Custom Oversize

Pick an engine or enter your nominal bore, choose an oversize, and see the bored-over displacement in ci, cc and liters — with the gain in cubic inches and percent computed live.

Stock displacement
349.8 ci
5733 cc
Bored-over displacement
355.1 ci
5819 cc
Gain
+5.27 ci
Percent
+1.51%
Finished bore
4.030"

Gain ≈ π/2 × nominal bore × oversize × stroke × cylinders. The finished bore is what final honing produces — order pistons against the as-honed bore, not this nominal math.

Section 1

What "Bored 30 Over" Means — and the Math Behind the Calculator

Overboring (the trade says "bored over," "bored oversize," or "bored .030") means machining every cylinder's diameter larger than the factory nominal dimension, then installing matching oversize pistons. A 350 Chevy with a 4.000-inch nominal bore, bored .030 over, now has 4.030-inch bores — and because displacement counts the whole swept cylinder, the engine grows too. The same operation renews worn, tapered cylinder walls, which is why an overbore is equal parts rebuild step and displacement bonus.

// the only formula the calculator runs
V = (π/4) × bore² × stroke × cylinders
new bore = nominal bore + oversize
// gain shortcut: ΔV ≈ π/2 × bore × Δbore × stroke × cyl

The shortcut line is worth a second look, because it explains why the percent gains stay small: the added ring of metal around each cylinder is thin, so the gain is roughly the cylinder's circumference times the oversize times the stroke. On the 350, .030 over works out to (π/2) × 4.000 × 0.030 × 3.48 × 8 = 5.27 ci — 349.85 → 355.1 ci, just over 1.5%. Bigger bores gain more per thousandth, which is why the same .060 adds about 13 ci to a 454 but under 3 ci to a 305.

Two clarifications that prevent mistakes: the increments are diameters (the radius grows by half as much), and they are per-bore — every cylinder is machined to the same oversize. Not sure what your bores actually measure today? Our cylinder bore measurement guide covers the gauge setup step by step.
Section 2

Bored-Over Displacement by Engine — Reference Table

Standard overbore results for common engines, computed from factory nominal bores — every value below is reproducible with the formula in Section 1, and the calculator at the top of this page recomputes any row with different stroke or cylinder counts.

EngineNominal bore × strokeStock+.030 over+.060 over
SBC 350 (8 cyl)4.000" × 3.48"350 cc355 cc360 cc
SBC 305 (8 cyl)3.736" × 3.48"305 cc310 cc315 cc
Ford 302 (8 cyl)4.000" × 3.00"302 cc306 cc311 cc
BBC 454 (8 cyl)4.250" × 4.00"454.0 ci460.4 ci466.9 ci
GM 5.3L (8 cyl)96 × 92 mm5327.3 ci5412.2 ci5497.8 ci
2JZ-GTE (6 cyl)86 × 86 mm2997.3 ci3050.7 ci3104.5 ci
D16Y8 1.6L (4 cyl)75 × 90 mm1590.4 ci1622.9 ci1655.7 ci

Inch engines shown in ci, metric engines in cc. Stock bore × stroke values reuse the factory specifications verified for our displacement chart (2026-11-02); all overbore columns are computed on this page.

Section 3

How Far Can You Bore? The Safe Ceiling on Any Overbore

The calculator will happily compute a +.125 overbore — whether the block can survive one is a different question. Three physical limits set the ceiling:

  • Cylinder wall thickness. Machinists sonic-check the walls and set the maximum safe bore for that specific casting. Thin walls ring, distort under head-bolt clamp, and crack under load — the safe maximum is a measurement, never a rule of thumb.
  • Bore spacing. The center-to-center distance between adjacent cylinders is fixed by the casting; the wider the spacing, the more room each bore can ever grow. This is an architecture-level limit — our big block vs small block guide shows how it separates engine families.
  • Piston availability. Oversize pistons are catalogued in standard steps — .010 through .060 in US sizes, 0.25 to 1.0 mm in metric sizes (industry-catalog conventions; your piston supplier's catalogue is the authority). A size with no piston catalogued is a size you cannot easily build.
⚠️ When walls are already thin: sleeving restores wall thickness and allows aggressive bores, at the cost of a sleeve-installation machining job. An experienced shop will tell you honestly whether your block wants one.
Machine shop boring bar machining an engine block cylinder to oversizeThe bore ceiling is measured, not guessedPhoto: Unsplash
Section 4

How Much Does It Cost to Bore an Engine? Real Published Prices

Boring is a machine-shop job, and its price is the most-asked follow-up after the displacement math. Rather than quoting folklore, here are two currently published US price lists (verified 2026-11-09) that show the real structure of the cost:

Kevin's Machine — published shop pricing
  • Bore & hone, 4-cylinder block$200
  • Bore & hone, 6-cylinder block$225
  • Bore & hone, 8-cylinder block$275
  • Single-cylinder hone$45

Source: kevinsmachine.com published services list, retrieved 2026-11-09.

Advanced Racing Engines — published shop rate
  • General shop labor rate$137.50/hr
  • Cylinder boring & honingquoted per block

Source: advancedracingengines.com published pricing page, retrieved 2026-11-09.

Data nature note: these are example prices from public price lists at one point in time — boring costs vary by region, bore size (big-block and metric bores cost more to set up), the block's condition, and whether decking, sonic checks or sleeves are added. Budget the bore-and-hone line item first, then let the shop's quote price the rest.

💡 What the price usually does not include: the oversize pistons themselves, decking, cleaning, crack inspection, and final assembly — machine-shop labor and parts are separate budget lines, and single-cylinder motorcycle work prices differently from automotive blocks. The engine rebuild process guide maps where boring sits in a full rebuild budget.
Section 5

Worked Example — Boring a 350 Small Block .060 Over, Step by Step

Here is the full arithmetic for the most common overbore in American V8 building, so you can see every number the calculator above produces — and one side effect it does not show by default. The small-block Chevy 350's factory dimensions are a 4.000 in bore and a 3.48 in stroke, so the stock swept volume is (π/4) × 4.000² × 3.48 × 8 = 349.8 ci.

  1. Finished bore: 4.000 + 0.060 = 4.060 in. This is the number the machinist targets with the final hone, and the number printed on the oversize piston boxes you order — pistons are sold by finished bore size, not by the cut amount.
  2. New swept volume: (π/4) × 4.060² × 3.48 × 8 = 360.4 ci (about 5,906 cc, or 5.9 L). The bore grew just 1.5%, but because swept volume scales with the square of bore, displacement rose 3.0%.
  3. The gain: 360.4 − 349.8 = +10.6 ci (+173 cc). That is the entire reward for the machine work — meaningful context for a displacement class, nearly invisible seat-of-the-pants. The honest framing: an overbore is paid for by the fresh, correct, round bores it leaves behind, not by the extra cubic inches.
  4. The compression side effect: the bore grew but the combustion chamber did not, so clearance volume stays roughly constant while swept volume rises. On a 10.0:1 350 (per-cylinder clearance ≈ 4.86 ci), the same heads on the .060-over block compute to about 10.27:1 — roughly a quarter point of compression for free. Run the new bore through the compression ratio calculator with your actual chamber cc before you order fuel, because an overbore can nudge a borderline combo over the detonation line.

Reading a Machinist's Overbore Quote

When the shop calls back with numbers, four phrases decide whether the block lives. A sonic check measures wall thickness before any cut — on thin-wall modern blocks it is the difference between a safe .040 and a water-jacket breakthrough at .060, so treat it as mandatory, not optional. Torque-plate honing simulates head-bolt clamping load while the final pass is made; it costs more and produces bores that stay round in the assembled engine. Final bore size on the invoice is the finished dimension — confirm it matches the pistons you ordered, because a bore cut to 4.060 with 4.030 pistons means another piston purchase. And deck height confirms whether the block was also squared, a separate budget line that changes compression ratio through deck clearance. Keep the invoice with the finished-bore number in the engine's build records — it is the dimension every future measurement, gasket order and rebuild quote will be checked against.

💡 One decision, one number: whatever oversize you and the shop settle on, the finished bore is the single input this page's calculator needs — enter it as the bore (nominal + oversize) and every result above, from ci to cc to the percent gain, follows from that one dimension.
Section 6

Big Bore Kits — Overboring in Scooter and Motorcycle Terms

On two-wheelers, the same operation is sold as a big bore kit: a larger-diameter cylinder and piston assembly (often with a matching head or liner) that raises displacement in one purchase. The arithmetic is identical to the automotive case, just smaller:

Worked example — GY6 125/150 scooter engine

The GY6 157QMJ engine's stock 57.4 mm bore × 57.8 mm stroke gives (π/4) × 5.74² × 5.78 cm = 149.6 cc — the honest math behind the "150cc" badge. Install a 63 mm big bore kit (Naraku's published product specification states the kit increases displacement to 180cc, verified 2026-11-09) and the same stroke computes (π/4) × 6.3² × 5.78 = 180.3 cc — a 20.5% gain, far larger than any car overbore produces, because the bore grew 9.8% of its nominal size. Scooter and motorcycle kits quote gains in whole cylinder classes for exactly this reason.

💡 Kit vs machine shop: small-engine big bore kits replace the cylinder outright, so "boring" happens at the factory — you bolt in the bigger bore. Automotive overboring machines your existing block. The displacement math on this page applies to both; just feed the kit's new bore as the finished dimension.
💡 Check the per-cylinder class: motorcycle and scooter engines are displacement-classed (125, 150, 180, 200cc racing classes). A big bore kit can move you into a different class or out of street-legal compliance — check the rules before the wrench turns.

Overbore & Displacement — FAQ

Roughly 1.5% on a V8 like the 350 Chevy: 349.8 ci becomes 355.1 ci, a gain of 5.3 cubic inches. The exact rule: displacement gain ≈ π/2 × bore × oversize × stroke × cylinders — with the oversize in inches. On a 4.000-inch bore that is 1.5708 × 4.000 × 0.030 × 3.48 × 8 = 5.27 ci. Because the gain scales with the stock bore, the same .030 adds less than a cubic inch on a 600cc motorcycle engine and over 7 ci on a 454.
Author / maintainer: Engine Calculator editorial team (site-wide byline) · Cost references: Kevin's Machine and Advanced Racing Engines published price lists (retrieved 2026-11-09); GY6 kit spec per Naraku product listing (retrieved 2026-11-09); factory bore × stroke data verified 2026-11-02 on the displacement chart. All displacements computed on this page.Last updated: 2026-11-09