3 Units at Once · Reverse Solver · ci ⇄ cc ⇄ L

Engine Displacement Calculator — Bore × Stroke × Cylinders

Enter bore, stroke and cylinder count — get engine displacement in cubic inches, cc and liters simultaneously. Work backwards from a known displacement to realistic bore/stroke combinations, convert between ci, cc and liters instantly, then carry your displacement into a compression ratio calculation.

Engine Displacement Solver — Bore × Stroke × Cylinders

✓ 4.0000 in = 101.6 mm

✓ 3.4800 in = 88.4 mm

Cubic Inches (ci)
349.85
Cubic Centimeters (cc)
5,733
Liters (L)
5.73
// live calculation — (π/4) × bore² × stroke × cylinders
area = π/4 × 4.00002 = 12.566 in²
per-cylinder = 12.566 × 3.4800 = 43.731 ci (716.6 cc)
total = 43.731 × 8 = 349.85 ci = 5,733 cc = 5.73 L
This engine displacement calculator is the upstream step of the Engine Calculator home page toolchain: once you know your swept volume, every compression ratio decision gets easier. Looking for the wider build toolkit? Browse the full calculator hub, and if you are still asking what displacement actually is, the engine displacement definition & formula guide explains every term in plain language.
The Formula

How the Engine Displacement Formula Works

Engine displacement is the total volume that all pistons sweep through as they travel from bottom dead center to top dead center. One cylinder contributes the volume of a cylinder whose diameter is the bore and whose height is the stroke: the circle-area formula πr² rewritten with diameter gives π/4 × bore², and multiplying by stroke turns area into swept volume. Multiply by the number of cylinders and you have the whole engine:

D = (π / 4) × bore² × stroke × cylinders

The π/4 factor exists because spec sheets quote diameter, not radius. If bore and stroke are in inches the result is cubic inches; if they are in millimeters the result is cubic millimeters, which you divide by 1,000 to get cc. Both paths land on the same engine — a 4.000 × 3.480 in V8 and a 101.6 × 88.4 mm V8 are the same hardware written in two languages, and both compute to 349.85 ci (5,733 cc).

Watch the two classic input mistakes. First, mixing units inside one calculation — a millimeter stroke in a formula fed with inch bores inflates the answer by a factor of 25.4 per dimension. Second, squaring the radius instead of the diameter: π × r² × stroke with r = bore/2 is correct, but π × bore² × stroke is not — it is four times too big, which is exactly why the formula carries the π/4.

Worked example — 350 small-block
bore = 4.000 in (101.6 mm)
stroke = 3.480 in (88.4 mm)
area = π/4 × 4.000² = 12.566 in²
per cyl = 12.566 × 3.480 = 43.731 ci
× 8 cylinders = 349.85 ci
= 349.85 × 16.387 = 5,733 cc = 5.73 L
Why the factory badge says 350:349.85 ci rounds to 350, and 5,733 cc rounds to 5.7 L. Nameplates round — the formula does not. When two engines are compared by badge numbers alone, up to 1.5% of the difference can be marketing rounding rather than metal.
Engine block cylinder bores being measured with a dial bore gauge for displacement calculationbore² does the heavy liftingPhoto: Unsplash
Unit Discipline

Mixing Imperial and Metric Inputs Without Conversion Errors

Real projects mix unit systems constantly: a Honda K24 spec sheet reads 87.0 mm bore and 99.0 mm stroke, while an American stroker catalog quotes 4.030 × 3.750 inches. The rule that prevents every conversion bug is simple — convert the dimension, not the formula. Pick one system, convert every input into it, then run π/4 × bore² × stroke × cylinders once.

The calculator above lets each field carry its own unit toggle precisely because that is how measurements arrive in the real world: a bore mic reads inches, a Japanese spec page reads millimeters. When you flip a field between in and mm, the entered value converts in place and the green confirmation line under the field shows both readings, so a 25.4× blow-up is visible instantly instead of showing up as a 25.4× displacement error.

1 in = 25.4 mm

Exact by international agreement since 1959. No rounding in the definition — 101.6 mm is 4.000 inches, not approximately.

1 ci = 16.387064 cc

That is 25.4³ mm³. Any source quoting "16.4" or "16.39" is rounding — fine for estimates, wrong for spec tables.

1 L = 1,000 cc

The only trivially clean one. Liters are just marketing cc: 6,162 cc becomes the friendlier 6.2 L badge.

One more trap worth naming: rounding too early. If you convert 86.0 mm to inches, get 3.386, and feed a rounded 3.39 into the formula, a six-cylinder engine loses roughly 8 cc of claimed displacement — invisible on a single build, but it compounds when you are verifying a chart of twenty engines. Keep full precision through the math and round only the final display, which is what the tool does.

Reference Data

Common Engine Bore and Stroke Reference Values

Nine verified engines spanning American V8s, Japanese fours and sixes, and a four-cylinder sportbike. Every displacement in the table is computed live from the bore, stroke and cylinder columns using the page formula — load any row into the calculator with one click and the outputs will match. Factory badge numbers are shown so you can see exactly how much rounding each manufacturer applies.

EngineBoreStrokeCylComputed ciComputed ccBadge
SBC 350Chevy small-block4.000 in3.480 in8349.85,733350
383 StrokerChevy stroker4.030 in3.750 in8382.76,271Stroker
LS3 6.2LGM Gen IV4.065 in3.622 in8376.16,1626.2L
LS7 7.0LGM Gen IV4.125 in4.000 in8427.67,0087.0L
Coyote 5.0Ford Modular3.630 in3.640 in8301.44,9395.0
Mopar 440Chrysler RB4.320 in3.750 in8439.77,206440
D16Y8 1.6LHonda D-series75 mm90 mm497.11,5901.6L
2JZ-GTE 3.0LToyota JZ86 mm86 mm6182.92,9973.0L
YZF-R6 600Yamaha sportbike67 mm42.5 mm436.6599600

Bore/stroke sources: GM LS and Ford Coyote figures as compiled in this site's compression-ratio preset library (factory service specifications); D16Y8, 2JZ-GTE and YZF-R6 verified against manufacturer spec sheets, last checked 2026-11-02. Computed columns derive from the formula on this page — recompute any row and the numbers must agree.

Reverse Mode

From a Known Displacement Back to Bore and Stroke

The reverse problem — this block is badged 383, what bore and stroke made it? — has a twist: one equation, two unknowns. Displacement constrains only the product bore² × stroke, so there is a continuous curve of solutions, from tiny bores with long strokes to huge bores with short ones. Engineering constraints, not math, pick the answer: stock cylinder walls limit overbore, deck height limits stroke, and valvetrain geometry prefers certain bore/stroke ratios.

Planning machine work rather than a matching exercise? When the block comes back bored .030 or .060 oversize, the overbore displacement calculator shows exactly how many cubic inches those cuts add — and if you are taking the before-measurements yourself, the guide to measuring cylinder bore covers reading a dial bore gauge without the common errors.

The reverse tab handles this by searching realistic bores (2.0–4.6 in — the span that covers everything from motorcycle singles to big-block V8s), solving the required stroke for each, and keeping only pairs where that stroke is physically plausible. It then ranks the survivors by closeness to a 1.05 bore/stroke ratio, because the majority of production engines cluster near-square: the 350 SBC is 1.15 (slightly oversquare), the 2JZ is exactly 1.00, and the R6 screams at 1.58.

Use the output as a shortlist, not an oracle. A solver row of 4.030 × 3.750 in for a 383 is meaningful because that is a real, orderable crank-and-piston package; a 3.2 × 5.3 pairing that hits the same total is thermodynamically identical but does not exist as hardware. Cross-check candidates against the engine displacement chart before you buy anything.

Why bore² × stroke, not bore × stroke
  • Volume scales with cross-sectional area, and a circle's area grows with the square of its diameter: +0.030 in on a 4.000 bore adds 12.57 in² × 0.030 = 0.377 ci per cylinder.
  • Stroke scales linearly: +0.250 in of stroke on that same 4.000 bore adds 12.57 × 0.250 = 3.14 ci per cylinder — strokers are so effective because stroke changes are eight times bigger than typical overbores.
  • Same 5 ci gain, two paths: overbore 0.400 in (impossible on a stock block) or stroke +0.334 in (a standard stroker kit). That asymmetry is why stroker kits dominate the displacement market.
Terminology cheat sheet
Oversquare — bore > stroke. Revs high, prefers RPM for power (Yamaha R6: 1.58).
Square — bore = stroke. The 2JZ's 86.0 × 86.0 mm.
Undersquare — stroke > bore. Torque-biased, low-RPM pull (Honda K24: 0.88).
Unit Conversion

The Conversions People Actually Search For

Every row below is computed from the exact factors — 1 ci = 16.387064 cc and 1 L = 1,000 cc — using the same code path as the converter tab. These are the high-traffic crossings: classic American displacements into metric, and modern metric badges into cubic inches.

Cubic InchesccLiters
350 ci5,7355.74 L
383 ci6,2766.28 L
427 ci6,9977.00 L
440 ci7,2107.21 L
454 ci7,4407.44 L
LitersccCubic Inches
5.0 L5,000305.1 ci
5.3 L5,300323.4 ci
5.7 L5,700347.8 ci
6.2 L6,200378.3 ci
6.7 L6,700408.9 ci

Note the near-misses that trip people up: 5.7 L is 347.8 ci, not 350 — the SBC badge and the liter badge describe the same engine rounded from opposite ends. And 6.2 L is 378.3 ci, which is why the LS3 (376.1 ci computed) and the Hellcat's 6.2 L supercharger marketing are both "6.2" while differing by two cubic inches.

Next Step

Displacement Is Not Compression Ratio — But One Feeds the Other

Displacement answers how much air the engine can hold at BDC. Compression ratio answers how much that air gets squeezed. They share the same anatomy — the swept volume you just calculated is the Vd term in the compression ratio formula CR = (Vd + Vc) / Vc — but a big engine with huge chambers can have a lower CR than a small engine with tiny ones. Displacement is capacity; compression ratio is a ratio. Neither implies the other.

That relationship is why this calculator exists as a separate tool rather than a dropdown in a compression calculator: builders measure bore and stroke first, compute displacement, then measure or target the clearance volume that produces the compression ratio they want. Doing it in the other order — guessing displacement from a CR target — fails the moment chamber cc differs from the catalog value, which it always does after machine work.

Ready for the next step? Run your displacement through the full compression ratio calculator on the home page, or if you already have a CR target and need the clearance volume it implies, the clearance volume calculator takes your displacement as its starting input — the exact number this page just produced.

Displacement
🫙

Swept volume only. An absolute number in ci/cc/L. Fixed by bore, stroke, cylinders.

Compression Ratio
🔀

A dimensionless ratio. Needs swept volume and clearance volume. Tunable by chamber, gasket, deck, piston.

CR = (Vd + Vc) / Vc — your displacement is Vd
Same displacement, three CRs:A 350 ci V8 with 76 cc chambers runs 8.5:1. The identical 350 ci with 64 cc chambers and a tight quench runs 10.5:1. Same air capacity, dramatically different squeeze — which is why racers speak of both numbers together.
FAQ

Engine Displacement Calculator — Frequently Asked Questions

Use Displacement = (π/4) × bore² × stroke × cylinders, keeping bore and stroke in the same unit. A 4.000 in bore × 3.48 in stroke V8 gives (π/4) × 16 × 3.48 × 8 = 349.85 cubic inches ≈ 350 ci, which converts to 5,733 cc or 5.73 L. The formula is just the volume of one cylinder (a circle times the piston travel) multiplied by how many cylinders the engine has.
Author / maintainer: Engine Calculator editorial team (site-wide byline) · All values recomputable from the formula on this page.Last updated: 2026-11-02